ENFLON ® (FILLED PTFE) COMPOSITIONS & FILL DESCRIPTIONS

 

ENFLON ® CODE #	CONSISTS OF	DEFINITION OF FILL
ENFLON 101 ENFLON 102 ENFLON 103 ENFLON 104 ENFLON 105 ENFLON 106	5% Glass Fiber 10% Glass Fiber 15% Glass Fiber 20% Glass Fiber 25% Glass Fiber 30% Glass Fiber	Milled glass fibers have the least effect on chemical and electrical properties and add greatly to the mechanical properties of unfilled PTFE. Addition of glass improves compressive properties by as much as 40% and improves wear resistance greatly. These compounds resist acids and oxidation but can be attacked by alkali.
ENFLON 110 ENFLON 111 ENFLON 112 ENFLON 113 ENFLON 114	5% Graphite 10% Graphite 15% Graphite 20% Graphite 25% Graphite	Graphite has good chemical resistance to corrosive environments and exhibits good initial wear and rubbing/sliding characteristics in dry and water applications. Commonly blended with carbon and PTFE.
ENFLON 115 ENFLON 116 ENFLON 118	25% Bronze 40% Bronze 60% Bronze	This filler has better wear, creep resistance, and higher thermal conductivity than glass fiber with PTFE. The compound is easily machined, but has poor chemical resistance in the presence of acids and alkali. Useful in applications which undergo high mechanical loads or high-speed rubbing contacts where the bronze filler supplies the strength and conductivity to carry away excess, unwanted heat.
ENFLON 127	5% Molybdenum Disulfide	This filler is used frequently in combination with others to increase surface hardness, stiffness, and to reduce the starting coefficient of friction and steady-state wear. Its effect on electrical and chemical properties is negligible.
ENFLON 130 ENFLON 131 ENFLON 132 ENFLON 133 ENFLON 134	5% Carbon 10% Carbon 15% Carbon 20% Carbon 25% Carbon	Carbon has good chemical resistance to corrosive environments. It exhibits good initial wear and rubbing or sliding contact characteristics, both dry and water applications. It is frequently used in piston rings to reduce cylinder wall wear by entrapping abrasive foreign particles in their relatively soft surfaces.
ENFLON 136 ENFLON 137 ENFLON 138	10% Carbon-Graphite 20% Carbon-Graphite 25% Carbon Graphite	These fillers are used both separately and together in PTFE compounds.
ENFLON 140 ENFLON 141 ENFLON 142	5% Calcium Fluoride 10% Calcium Fluoride 15% Calcium Fluoride	ALTERNATIVE TO GLASS FILL.
ENFLON 151 ENFLON 152 ENFLON 153 ENFLON 155	15% Glass Fiber, 5% Moly 20% Glass Fiber, 5% Moly, 5% Carbon-Graphite 23% Glass Fiber, 2% Moly 25% Glass Fiber, 5% Moly	SEE ABOVE FOR INDIVIDUAL DEFINITIONS.
ENFLON 157 ENFLON 158 ENFLON 159	10% Glass Fiber, 10% Graphite 5% Glass Fiber, 5% Graphite 20% Glass Fiber, 5% Graphite	SEE ABOVE FOR INDIVIDUAL DEFINITIONS.
ENFLON 161 ENFLON 162	10% Glass Fiber, 5% Carbon 5% Glass Fiber, 10% Carbon	SEE ABOVE FOR INDIVIDUAL DEFINITIONS.
ENFLON 170 ENFLON 171 ENFLON 172 ENFLON 173	40% Bronze, 5% Moly 40% Bronze, 10% Moly 55% Bronze, 5% Moly 65% Bronze, 5% Moly	SEE ABOVE FOR INDIVIDUAL DEFINITIONS.
Upon Request, physical testing with test reports available.

PTFE & ENFLON ® TYPICAL PHYSICAL PROPERTIES OF VIRGIN PTFE PRODUCTS

COMMON SPECIFICATIONS FOR Teflon ® AND PTFE PRODUCTS

Specifications *AMS 3651 AMS 3652 AMS 3656 AMS 3658 AMS 3659 AMS 3660 AMS 3661 AMS 3662 AMS 3667 AMS 3668 AMS 3669 AMS 2491 *MIL-P-22241 *MIL-P-19468 ASTM D1710 ASTM D3293 ASTM D3294 ASTM D3308	Type Of Specification for PTFE and Teflon ® PTFE RODS, TUBES, SHEETS, SHAPES (See AMS 3652 thru AMS 3669) PTFE FILM PTFE EXTRUSIONS PTFE EXTRUSIONS PTFE EXTRUSIONS PTFE MOLDINGS PTFE FILM PTFE FILM PTFE SHEET, MOLDED PTFE MOLDINGS PTFE SHEET, MOLDED SURFACE TREATMENT OF PTFE PTFE SHEET & FILM (See ASTM D3293 & ASTM D3308) PTFE RODS, MOLDED & EXTRUDED (See ASTM-D1710) PTFE ROD PTFE MOLDED SHEET PTFE MOLDED SHEET OR SHAPES PTFE SKIVED TAPE
* Note: These specifications have been deleted. See replacement specifications for current information.
Upon Request, physical testing with test reports available.